FREE Noise / Sound Enclosure - fits the Blendtec Blenders
The Blender Noise / Sound Enclosure Box has been designed to fit the dimensions of the - Blendtec HP3A Blender
- Blendtec EZ Blender
- Blendtec Total Blender
Above
to the left is the Blendtec EZ Blender, which is a 3 hp commercial
version of the Blendtec HP3A and the Blendtec Total Blender. All of
these have a 3 hp motor for power and a 13 AMP 1500 Watts power supply.
The Total Blender looks just like it. The only difference on the Total
Blender is the alphanumeric keypad and 16 pre-programmed blending
cycles versus the 25 program cycles and the numeric keypad buttons on
the Blendtec HP3A.
The dimensions of these Blenders are 7 inches wide, 8 inches deep (the base), and
15.5
inches tall. Our design of the blender sound enclosure box that fits
these Blendtec Blenders consists of outside dimensions 9.5 inches wide,
10 inches deep, and 16.50 inches tall, (with the height of the top lid
hinges, it is about 16.75 inches tall). The material thickness is 3/16
inch FDA-compliant / rated acrylic.
The dimensions of these Blenders are 7 inches wide, 8 inches deep (the base), and
15.5
inches tall. Our design of the blender sound enclosure box that fits
these Blendtec Blenders consists of outside dimensions 9.5 inches wide,
10 inches deep, and 16.50 inches tall, (with the height of the top lid
hinges, it is about 16.75 inches tall). The material thickness is 3/16
inch FDA-compliant / rated acrylic.Right: Blender Noise / Sound Enclosure Box designed to fit the
Blendtec Blenders and how it will be delivered to you.
Just pull off the protective paper and it will look like this
The
blender noise level dB (DECIBELS), of any of these blenders is between 95 dB to
105 dB according to our dB meter measuring device. And certainly you
won't need a decibels meter to know that these rather strong and
powerful blenders are noisy. Now, the 'noisy; statement is not a
complaint as if it was a horrible thing. There is just nothing that can
be done. The only alternatives are:- Live and Eat with it
- Get a Blender Sound Enclosure Box
- Or don't use the blender
Any
other blenders that are less noisy don't have the power that it takes
to break the cell walls for optimum phyto-nutrient release. These less
powerful 
blenders
also break down quickly after just a few raw smoothies and soups
attempts. We actually believe it is wise to use a sound enclosure box.
It will help in your family relations, and it will make the
soup-blending process easier on you. Also, contained noise will
hopefully result in healthier nutrient intake in form of smoothies and
raw soups more frequently.
Why is raw blended soup so advantageous over cooking a soup? That is an easy answer. The answer is in the RAW. When cooking, even boiling raw ingredients, most nutrients are being reduced to taste... not much left. To the other hand, making soup in a blender takes about 5 minutes or little less. It is at about 100 dB or less. Again, think it over if a Blender Sound Enclosure Box is for you.
We also have a Blender Noise / Sound Enclosure Box designed to fit the Vitamix 5200 Total Nutrition Center Blender, the Vita Mix 4500 Turbo Blender, the Vita Mix Vita Prep 2 hp and 3 hp Blenders, and any alike blenders with equal dimensions. Please check them out.
The Blender Noise / Sound Enclosure Box designed for the Blendtec HP3A, Total Blender, and EZ Blenders (3 hp blenders) is 9 1/2" wide by 10" deep and 16 1/2" tall. Its total net weight is 6 pounds. The material is made from 3/16" thick Cell-Cast Acrylic. The sound enclosure box features a lid on top of the box that opens up and left, allowing the user to access the Blendtec HP3A 3 hp blender from the top to add more ingredients. Very Important: Please see our Warranty and Disclaimer Section for more information
blenders
also break down quickly after just a few raw smoothies and soups
attempts. We actually believe it is wise to use a sound enclosure box.
It will help in your family relations, and it will make the
soup-blending process easier on you. Also, contained noise will
hopefully result in healthier nutrient intake in form of smoothies and
raw soups more frequently.Why is raw blended soup so advantageous over cooking a soup? That is an easy answer. The answer is in the RAW. When cooking, even boiling raw ingredients, most nutrients are being reduced to taste... not much left. To the other hand, making soup in a blender takes about 5 minutes or little less. It is at about 100 dB or less. Again, think it over if a Blender Sound Enclosure Box is for you.
We also have a Blender Noise / Sound Enclosure Box designed to fit the Vitamix 5200 Total Nutrition Center Blender, the Vita Mix 4500 Turbo Blender, the Vita Mix Vita Prep 2 hp and 3 hp Blenders, and any alike blenders with equal dimensions. Please check them out.
The Blender Noise / Sound Enclosure Box designed for the Blendtec HP3A, Total Blender, and EZ Blenders (3 hp blenders) is 9 1/2" wide by 10" deep and 16 1/2" tall. Its total net weight is 6 pounds. The material is made from 3/16" thick Cell-Cast Acrylic. The sound enclosure box features a lid on top of the box that opens up and left, allowing the user to access the Blendtec HP3A 3 hp blender from the top to add more ingredients. Very Important: Please see our Warranty and Disclaimer Section for more information
Learn to build your own Blender Noise/Sound Enclosure Box for FREE!
PURCHASE NOW: We will ship your Parts Kit within 7 days and your assembled Noise/Sound Enclosure within 10 days
 1 Blender Noise/Sound Enclosure Box Kit for self-assembly that fits the Blendtec Blenders: USD $ 49.50 Blender Noise/Sound Enclosure Kit for self-assembly that will fit the Blendtec HP3A & alike Blenders - see Warranty Instructions to assemble available online See Disclaimers and Warranty Information Call 801-623-3225 for more information |  1 Assembled Blender Noise/ Sound Enclosure Box with 6 months Warranty, designed to fit the Blendtec Blenders:
USD $ 69.50 Complete Noise/Sound Enclosure Box Assembled with 6 months Warranty See Disclaimer and Warranty Information |  Add 6 months extra Warranty Limited to the USA and Canada USD $ 20.00 |
See Warranty Information and Disclaimers
USE AND CARE
The
front door allows you to load and unload the blender Jar / Container to
and from the
blender in the blender sound enclosure box. You simply open the fron
t
door on the right towards the left (hinge side custom modification is
possible) and grab the Blendtec Container / Jar by the handle, and move
it upwards
about 1 inch (this will open the top lid upwards). Then move the
container
out by slightly dipping the top towards the back and the bottom towards
you. And when you use it, you will, see it is really not as complicated.
We installed a
front top bar and panel for stability. The front bottom panel adds also stability
to the sound box. The door access in the front gives you perfect load/unload and blender control. The keypad is easy reachable.
The factory has advised us to allow ample ventilation so the blenders won't overheat while operating inside a sound enclosure. These ventilation areas are on the left and right side panels on the bottom 3/8" inches by 9 1/2" inches. Either side of the ventilation areas can be used to exit the power cable. Please note, we do not guarantee whether the ventilation area is sufficient. A blender may overheat whether or not you are using a sound enclosure box. It depends on 'how' use, frequency of use, what ingredients are used, how old the blender is and so on... many variables exist. Our design in our opinion is adequate for the ventilation. If you are concerned, you can make these ventilation areas bigger, or request a custom modification of your assembled sound enclosure box, or the parts kit you desire to buy from us. And if you have your own design, well, you are welcome to copy ours with your own modification(s) and make your own box. SEE WARRANTY AND DISCLAIMER SECTION for more info. Hopefully you can tell us about your own improvements.
Wash the acrylic with liquid soap and warm water carefully, using a soft sponge or towel. Don't use anything that could scratch the acrylic surface.
The factory has advised us to allow ample ventilation so the blenders won't overheat while operating inside a sound enclosure. These ventilation areas are on the left and right side panels on the bottom 3/8" inches by 9 1/2" inches. Either side of the ventilation areas can be used to exit the power cable. Please note, we do not guarantee whether the ventilation area is sufficient. A blender may overheat whether or not you are using a sound enclosure box. It depends on 'how' use, frequency of use, what ingredients are used, how old the blender is and so on... many variables exist. Our design in our opinion is adequate for the ventilation. If you are concerned, you can make these ventilation areas bigger, or request a custom modification of your assembled sound enclosure box, or the parts kit you desire to buy from us. And if you have your own design, well, you are welcome to copy ours with your own modification(s) and make your own box. SEE WARRANTY AND DISCLAIMER SECTION for more info. Hopefully you can tell us about your own improvements.
Wash the acrylic with liquid soap and warm water carefully, using a soft sponge or towel. Don't use anything that could scratch the acrylic surface.
Delivery and Unpacking
The assembled blender sound enclosure box is going to be delivered
about 95% wrapped in its original protective paper / vinyl. When
unpacking don't use a large knife that could penetrate the protective
paper and scratch the acrylic. Also, use much care unwrapping it
slowly. Do not use excessive force. See Build Instructions on the bottom to learn about things to do and what not to do!
Finished Blender Noise/Sound Enclosure Box in its Protective Paper
A word of caution & Disclaimers
Building or assembling
the blender sound enclosure box is like making cookies. It is not
difficult to do if you follow the instructions. It would be beneficial
if you had acrylic assembly experience (for example with the IPS #
3(TM) Solvent), it would help you to assemble a beautiful box. If you
mess it up, you have to keep looking at it for years to come. To the
other hand, there is a significant money savings when assembling your
own blender sound enclosure box. It does take a good 1 hour to
assemble. And then you have to let the sound enclosure cure for about
30 hours.
Usual mistakes or problems occur when not experienced working with acrylic and bonding adhesive are: run-off that results in cosmetic blemishes, falling apart or not holding together very well, and having to redo the installation of doors and the hinges may become necessary. Remember, once acrylic has bonded and has cured, only a hammer will break off e.g. wrong installed hinges. And that will really destroy your box. So be careful and follow our installation instructions. And if not sure, let us do it for you. Please note, we are not responsible for you messing up the parts kit and no refunds will be given if you decide to assemble the blender sound enclosure box parts kit yourself.
Usual mistakes or problems occur when not experienced working with acrylic and bonding adhesive are: run-off that results in cosmetic blemishes, falling apart or not holding together very well, and having to redo the installation of doors and the hinges may become necessary. Remember, once acrylic has bonded and has cured, only a hammer will break off e.g. wrong installed hinges. And that will really destroy your box. So be careful and follow our installation instructions. And if not sure, let us do it for you. Please note, we are not responsible for you messing up the parts kit and no refunds will be given if you decide to assemble the blender sound enclosure box parts kit yourself.
